WARNING: This Product Contains Nicotine. Nicotine is an addictive chemical.

Railbox Mod by Vape.Tools

(No reviews yet) Write a Review
1.00 LBS
Calculated at Checkout
Max Wattage:
1W - 50W

Frequently Bought Together

Please choose options for all selected products

  • Choose Options

Videos Hide Videos Show Videos


The Vape Tools Railbox is an elegant and sleek box mod with head turning features that was designed and produced in Brittany, France. Although the Railbox by Vape Tools may look like a simple box mod, the attention to detail that was put into the Railbox is phenomenal and you can really feel the quality of the mod once held in the hand. The Railbox by Vape Tools takes a single 18650 battery and uses the Evolv DNA40 chip.

Your atomizer is placed inside the Railbox by removing the ball bearing sliding back panel and threaded onto the brass 510 connection on aluminum rails. You can use your thumb to slide the rail up and down to fit different sized atomizers with the largest atomizer being 24mm in diameter x 61mm in height excluding the drip tip.

The Railbox has 4 slits on the side of the mod near the drip tip to serve as air inlets to feed air into your atomizer and for battery venting. On the opposite side of the air inlet/vent holes are the firing button and the wattage adjusting buttons.

To use the Railbox, you will first need to remove the drip tip from the atomizer you would like to use inside the Railbox and thread your atomizer onto the 510 connection. Once your atomizer is threaded onto the 510 connection, you simply need to slide your atomizer up into the drip tip extension. Lastly, place your preferred drip tip into the top of the box.

With most quality built mods, one would expect it to be on the heavier side. However, the Railbox by Vape Tools is surprisingly light and the perfect mod to add to your arsenal!

The Railbox by Vape Tools utilizes the DNA40 temperature control chip designed and made in the U.S. by Evolv Vapor. The 40 watt chip reads resistance down to 0.16Ω for Kanthal builds and 0.10Ω for Nickel builds. The temperature can be adjusted from 200º to 600º Fahrenheit. Other features of the DNA40 chip include coil preheat, step up/down, synchronous rectification to extend battery life, and lower heat generation. The display screen shows battery life, resistance, temperature, and wattage setting.

Features and Specifications:

  • Dimensions: 96mm high x 30mm deep X 62mm wide max
  • Box Aluminium 5083 Anodised (AW5083/AW-AIMG4.5Mn07)
  • Aluminum Rail
  • Ball-Bearing Sliding Battery Door (Texalium or Epoxy Finish)
  • Internal Brass 510 Connection (Fits Up To 24mm in Diameter x 61mm in Height Excluding Drip Tip)
  • Fire Button: Inox
  • Switch: Inox
  • Evolv DNA 40 Chip
  • Compatible with 18650 and 16650 Batteries


1x Railbox Mod by Vape Tools

Warning: This product is for advanced users only and proper precautions/handling should always be used. Never use any atomizer on a hybrid mod with a 510 connection that is flush or shorter than the 510 threading of the atomizer to avoid any possible injuries.
Disclaimer: Please use extreme caution when working with Li-Ion (Lithium-Ion), LiPo (Lithium-Ion Polymer) and any other rechargeable batteries. The user should have fundamental knowledge of batteries and battery safety before using these types of batteries to avoid injury. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. Do not use any rechargeable battery as well as any battery charger if any visible damage is present, as well as if the cell or charger has been stressed through mishandling or accidental causes even if damage may not be visible. Always store and transport rechargeable cells in a safe, non-conductive container in a controlled environment. Dispose of all battery cells and chargers in accordance to local laws and mandates. Eciggity will not be held responsible for any damage or injury caused by misuse or mishandling of Li-Ion, LiPo and any other rechargeable batteries.
[ ]