<<<<<<< HEAD <<<<<<< HEAD ======= >>>>>>> 42a94ccd... CRO-97: Storefront admin bar ======= >>>>>>> 9f4433ac... STENCIL-3672 - Upgrade dependencies

Mesh PRO RDA by Digiflavor

$27.99
(5 reviews) Write a Review
Weight:
0.32 LBS
Shipping:
Calculated at Checkout

5 Reviews Hide Reviews Show Reviews

  • 5
    Excellent

    Posted by Darrel Madden on May 11, 2018

    Been running this atty on temp control using SS mesh for a few weeks and changed the cotton once just to see the status of the cotton and it was still in good shape. Flavor is top notch. Building is easy as it gets. I am impressed that the mesh builds can run on anything I throw at it : Mech, Un/regulated, and TC. DF did a great job with this.

  • 5
    Mesh Pro by Digiflavor

    Posted by Jason Tuck on Mar 23, 2018

    Best mesh vape ever. Simple to build on. Just make sure the mesh traps the cotton and compresses it, The wicking is the most difficult aspect and it is easy as long as you cram the cotton in there. Great air flow and the flavor is out of this world. All my juices taste different and better than conventional wick and coil.

  • 5
    My favorite

    Posted by Brandon Barrington on Feb 16, 2018

    Been vaping 4 years now and this is my favorite dripper Ive had. Amazing flavor. Insanely easy to build and wick. Great airflow. Only thing I would personally change is the hight of the drip tip. Its shorter than I am used to.

  • 5
    Fantastic performer if built right

    Posted by hazozita on Feb 07, 2018

    This has become one of my favorite attys. The flavor off the mesh is fantastic, and the airflow is as smooth as silk. It is, however, pretty unforgiving if it is not wicked correctly. The best way is to trap one edge of the mesh, add a big load of cotton, then trap the second edge of the mesh. That way the cotton is firmly compressed under the mesh and makes full contact. This will eliminate hot spots and dry hits. I prefer the Ni80 mesh, but the SS and Kanthal mesh also perform well. Although it comes with a squonk pin, this is much better performer if you drip. You can drip a LOT without leakage since the large mass of cotton plus the deep well holds a large volume of juice.

  • 5
    My all time favorite RDA

    Posted by Chris on Jan 21, 2018

    I have seen many bad reviews about mesh but I truly believe it's from people who have not invested the time to sort it out. I have used a Vandy Mesh since it came out and spent about 2 months with this RDA on a LV Drone Sqounk mod and I have to say I find this RDA spectacular and it's one everyone should have 2 of! So forgive the wall of text but I'm going to lay out why I love it.
    I have tried this with many types of mesh, SS316 mesh(150 ga, 200 ga, and 400ga), NI80 mesh, kanthal mesh and coils. I find the Ni80 to be my favorite but the 150 ga SS316 mesh is fantastic as well if TC is your thing. As far as the higher ga mesh, it tends to burn horribly rather than not fire when it's dry. *Also be sure not to use any galvanized ss316. I spent a good amount of time figuring out how best to build and wick the mesh. Tightly rolling the cotton as dense and tight as possible under the mesh is best, then really fray the ends down into the juice well. If it's wicked loose it will burn frequently and after a few days the cotton will sag leading to unavoidable dry hits. I also keep the mesh as short as possible to avoid it getting to hot. If you like a hot vape use about a .15 ohm strip (for Ni80 and .09 ohm rated 150ga SS316) When properly wicked each build will last about 2-3 weeks depending on what juice you use. It is also very consistent, as in that whether you just dripped or the wick is fairly dry it will taste and perform the same. Once your build has worn out you can not dry burn and rinse to reuse the mesh but re meshing takes hardly any time because you don't have to work out hot spots, and it's cheap. I can build and wick this RDA in about 1 minute with mesh. Single coils are easy to with the clamps and it's easy to fit big coils. I do find some troubles using some dual coils and not getting them clamped evenly.
    Flavor wise I find this to be very consistent and very different than coils but good. Not quite as intense as a Goon or Aromamizer but it's a very smooth and very sweet flavor from the mesh. I find this best with Desert, cereal and fruit flavors but prefer coils for tobacco's and creams. I mostly use sweet desert flavors so this is my go to every day RDA. If you are one who likes that throat hit then you may not care for the mesh. With coils in this RDA it's about the same as any old velocity type RDA.
    For those that use squonking mods, this RDA works great for any mods that can go down to about .12 ohm for the mesh, for coils it's business as usual. Again, if you build the mesh longer than about .12 it gets way too hot. Its also great that it doesn't leak unless you really over drip.
    I have to say that if I could only have just 1 RDA it would be this Mesh Pro. Overall ease of use, and the smoothness are untouchable. Flavor is different but for me and my desert flavors it is better than coils and more consistent. It's great for beginners too since it is so easy to build with mesh. It's also great for veterans because it will make all of your juices taste new in a way. For $30 this is a no brainier, give it a go!

The Mesh PRO RDA by Digiflavor is 25mm in diameter and features a user-friendly postless clamp design. Designed for simple mesh wire installations, the Mesh PRO also accommodates all wire types and single or dual coil configurations. Featuring an elevated deck with a deep juice well, the Mesh PRO is capable of holding a respectable amount of E-Juice to extend wick saturation. In addition, the Mesh PRO features dual adjustable direct side airflow which can be adjusted by turning the knurled top cap.

Features:

  • 25mm Diameter
  • Stainless Steel Construction
  • Postless Clamp Design
    • Accommodates Mesh, Single & Dual Coil Configurations
    • Elevated Gold Plated Deck
    • Spring Loaded Gold Plated Clamps
    • PEEK Insulator
  • Deep Juice Well
  • Dual Adjustable Side Airflow
    • Knurled Top Cap To Adjust Airflow Setting
  • 510 & 810 Drip Tip Compatible
  • Squonk Mod Compatible
  • Gold Plated 510 & Squonking Pin


Includes:

1x Mesh PRO RDA by Digiflavor

1x 810 Delrin Wide Bore Drip Tip

1x 510 Drip Tip Adaptor

2x KA1 Mesh Wire Strands

2x Ni80 Mesh Wire Strands

2x SS316L Mesh Wire Strands

1x Gold Plated 510 Pin

1x Gold Plated Squonk Pin

1x Bag Of Spare Parts

1x User Manual


Warning: This product is for advanced users only and proper precautions/handling should always be used. Never use any atomizer on a hybrid mod with a 510 connection that is flush or shorter than the 510 threading of the atomizer to avoid any possible injuries.

Disclaimer: Please use extreme caution when working with Li-Ion (Lithium-Ion), LiPo (Lithium-Ion Polymer) and any other rechargeable batteries. The user should have fundamental knowledge of batteries and battery safety before using these types of batteries to avoid injury. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. Do not use any rechargeable battery as well as any battery charger if any visible damage is present, as well as if the cell or charger has been stressed through mishandling or accidental causes even if damage may not be visible. Always store and transport rechargeable cells in a safe, non-conductive container in a controlled environment. Dispose of all battery cells and chargers in accordance to local laws and mandates. Eciggity will not be held responsible for any damage or injury caused by misuse or mishandling of Li-Ion, LiPo and any other rechargeable batteries.